MICRO USB 5V 2/4/8 Channel USB Control Relay Module 1 Channel 5-30V Delay Relay

Description

Visit store
Items for sale
About us
Product Details
4 Channel
2 Channel
8 Channel
1.The module have MICRO USB and serial port , so they can communicate with PC and other device conveniently.
2.The normal working voltage for modules is 5V.And module of ICSE014A have a power interface of 5V. Parameters are as follows:
ICSE012A
ICSE013A
ICSE014A
U
nit
R
emark
CC
4
2
8
channel count of module
I
400
250
700
mA
working current
U
5
5
5
V
input voltage
√
√
√
whether have serial port
9600
9600
9600
bit/s
baud rate of serial port
F
1000
1000
1000
Hz
Module control frequency
×
×
√
Whether have power interface
Interface:
Modules all have Micro USB and serial port . Read following for details：
1.Micro USB: Standard micro USB mother mouth.
2.TX : Transmit
3.RX : Receive
4.5V : Volt current condenser
5.GND : Ground
6.Power Interface : Only ICSE014A have . Interface is used when Micro USB cannot give enough power.
Usage method:
USB usage method
Module connect with PC through USB . The connection method is as follows:
1.Then open ”Relay Board Manager” to operate the module . Read ” RelayBoardManager_Reference” for details of the software.
Serial port usage method
Module can communicate with other device directly through serial port .
Module can receive single byte from upper monitor ( baud rate 9600)：
Upper Monitor 0x50 0x51
ICSE012A 0xAB
ICSE013A 0xAD
ICSE014A 0xAC
Module will turn to normal work state after receive “0x51” . Then every data byte will control the relay directly . Each bit controls a realy ( ‘0’ mark start , ‘1’ mark stop ) . Read following for details:
B
it
ICSE012A
ICSE013A
ICSE014A
Remark
0
√
√
√
Control the relay K1
1
√
√
√
Control the relay K2
2
√
×
√
Control the relay K3
3
√
×
√
Control the relay K4
4
×
×
√
Control the relay K5
5
×
×
√
Control the relay K6
6
×
×
√
Control the relay K7
7
×
×
√
Control the relay K8
Package included:
1pcs
1 Channel Delay Relay
Highlights:By adjusting the potentiometer can set the length of time.MicroUSB 5.0Vpower supply with an input port, easy to use.5 ~ 30Vwide supply voltage.External signaltrigger and keytriggerin two ways.
With a relay indicator.Antiinterference ability, the relay at various interference will not misoperation, suitable for industrial control.
1. Working voltage:wide voltage 5 ~ 30V, two power supply interface
2. Operating mode:the initial state, module outputs: normally open (NO) and the common terminal (COM) is disconnected,
normally closed (NC) and the common terminal (COM) connected.Providing a low pulse signal, or touch trigger key, relay and indicator lights,
the output of the state: normally open (NO) and Common (COM) connected,normally closed (NC) and the common terminal (COM) is disconnected.
After 0-24 seconds (this time can be adjusted according to your needs) relay off,back to the state before the trigger.
3.The length of timing adjustment by potentiometer, default 0-24 seconds.If you need more time, you can replace the larger capacitor (C2) or potentiometer.
Delay time T = 1.1RC. For example: 22uf capacitor and resistor 1M,then T = 1.1 * 0.000022 * 1000000 = 24.2 seconds.
4. With a relay indicator.5. The module can control: 10A / 250VAC, 10A / 30VDC load.6. The relay has a freewheeling protection.7. Trigger signal input terminal is designed with a pull and filter circuit,
enhanced anti-jamming capability, suitable for industrial control.
Many manufacturers add the optocoupler isolation,but there is no separation between module’s ground and signal’s ground,
would not achieve the interference effect.After the test found that only enhance the stability of the signal input port to interference,
regardless of this module is under electromagnetic interference environment,or in the power-up and power-down moment, the relay will not producemisoperation.
Dimensions:
5.4 * 1.9 * 1.8cm (L * W * H)9. Weight: 16g
Applications:
1. Burglar, alarm, building delay switch, sound and light control light switch.
2. Delay powered vehicle equipment, to prevent large currents generated as the car starts burning vehicle equipment.
3. Prevent simultaneous launch multiple devices cause burning appliances or fail to start.
Package included:
1*5-30V Micro USB Power Trigger Delay Relay Timer Control Switch Module
Payment Method
Shipping Policy
Returns & Refund Policy
Feedback
Payment Method
EBAY Managed Payment.
But we only
Accept
your
Ebay Address
, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
Returns & Refund Policy
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.